Mouse Glycogen Synthase (GSK) ELISA Kit Instructions for Use This kit is for research use only.
Drug Name:
Generic name: Mouse Glycogen Synthase (GSK) ELISA Kit
purpose of usage:
This kit is used to determine the content of glycogen synthase (GSK) in mouse serum, plasma, or other related tissue fluids.
Experimental principle:
This kit uses the double antibody sandwich method to determine the level of mouse glycogen synthase (GSK) in the specimen. Coat the microplate with purified mouse glycogen synthetase (GSK) antibody, add glycogen synthase (GSK) to the microwells in sequence, and then combine with HRP-labeled glycogen synthetase (GSK) antibody to form an immunity After thorough washing, the compound is added with TMB to develop color. TMB is converted into blue under the catalysis of HRP enzyme, and into the final yellow under the action of acid. The color depth is positively correlated with the glycogen synthase (GSK) in the sample. The absorbance (OD value) was measured with a microplate reader at a wavelength of 450 nm, and the concentration of mouse glycogen synthase (GSK) in the sample was calculated by a standard curve.
Kit composition:
1 20 times concentrated washing solution 30ml × 1 bottle 7 stop solution 6ml × 1 bottle
2 Enzyme label reagent 6ml × 1 bottle 8 standard (540pmol / L) 0.5ml × 1 bottle
3 Enzyme label coated plate 12 wells × 8 strips 9 standard dilutions 1.5ml × 1 bottle
4 Sample diluent 6ml × 1 bottle 10 instructions 1 copy
5 Developer A solution 6ml × 1 bottle 11 2 sealing film
6 Developer B liquid 6ml × 1 / bottle 12 sealed bag 1
Specimen requirements:
1. Experiment as soon as possible after specimen collection.
2. The samples containing NaN3 cannot be detected because NaN3 inhibits horseradish peroxidase (HRP) activity.
3. The specimen can be stored at -20 ℃, but repeated freezing and thawing should be avoided.
Steps:
1. Dilution and loading of standard products: set 10 standard wells on the enzyme-coated plate, add 100 μl of the standard products in the first and second wells, and then add the standard products in the first and second wells. 50μl of diluent, mix well; then take 100μl from the first well and the second well and add them to the third and fourth wells respectively, and then add 50μl of standard dilution solution to the third and fourth wells respectively, mix well Then take 50μl each in the third and fourth wells and discard it, then add 50μl each to the fifth and sixth wells, and then add 50ul of the standard dilution solution to the fifth and sixth wells respectively, and mix well; After mixing, take 50μl from the fifth and sixth wells and add them to the seventh and eighth wells respectively. Then add 50μl of standard dilution solution to the seventh and eighth wells respectively. Take 50μl from the eight wells and add them to the ninth and tenth wells. Then add 50μl of the standard dilution solution to the ninth and tenth wells respectively. After mixing, take 50μl from the ninth and tenth wells and discard. (After dilution, the volume of each well is 50μl, and the concentrations are 360pmol / L, 240pmol / L, 120pmol / L, 60 pmol/L, 30 pmol/L).
2. Add samples: set up blank wells (the blank control wells do not add samples and enzyme reagents, the rest of the steps are the same) and the sample wells to be tested. Add 40μl of sample diluent to the test sample well of the enzyme-coated plate, and then add 10μl of the test sample (the final dilution of the sample is 5 times). Add the sample and add the sample to the bottom of the well of the microplate, try not to touch the wall of the well, shake gently to mix.
3. Incubation: seal the plate with the sealing film and incubate at 37 ° C for 30 minutes.
4. Mixing solution: dilute 20 times concentrated washing liquid with distilled water 20 times and reserve
5. Washing: Carefully peel off the sealing film, discard the liquid, spin dry, fill each well with the washing solution, let it stand for 30 seconds and discard, repeat 5 times and pat dry.
6. Add enzyme: add 50μl of enzyme label reagent to each well, except blank well.
7. Incubation: The operation is the same as 3.
8. Washing: The operation is the same as 5.
9. Color development: Add 50μl of developer A to each well, and then add 50μl of developer B, mix gently, and develop for 15 minutes in the dark at 37 ℃.
10. Termination: Add 50μl of stop solution to each well to stop the reaction (at this time, the blue color turns to yellow).
11. Determination: Measure the absorbance (OD value) of each well in sequence with the blank air conditioner at zero and 450 nm wavelength. The measurement should be carried out within 15 minutes after adding the stop solution.
Calculation:
Taking the concentration of the standard as the abscissa and the OD value as the ordinate, draw a standard curve on the coordinate paper, and find the corresponding concentration from the standard curve according to the OD value of the sample; multiply by the dilution factor; or use the concentration of the standard Calculate the linear regression equation of the standard curve with the OD value, substitute the OD value of the sample into the equation, calculate the sample concentration, and multiply it by the dilution factor to obtain the actual concentration of the sample.
Precautions:
1. The kit should be taken out of the refrigerated environment and equilibrated at room temperature for 15-30 minutes before use. If the enzyme-coated plate is unsealed after opening, the strip should be stored in a sealed bag.
2. Crystals may be precipitated in the concentrated washing liquid, which can be heated and dissolved in a water bath during dilution, and the results will not be affected during washing.
3. The sampler should be used at each step of sample addition, and the accuracy should be regularly checked to avoid test errors. It is best to control the sampling time within 5 minutes. If there are many specimens, it is recommended to use a volley gun to add samples.
4. Please make a standard curve at the same time of each measurement, it is best to make a double hole. If the content of the substance to be tested in the specimen is too high (the OD value of the sample is greater than the OD value of the first well of the standard well), please dilute it with a certain multiple (n times) of the sample diluent and then determine it. Multiple (× n × 5).
5. The sealing film is limited to one-time use to avoid cross-contamination.
6. Strictly follow the instructions, and the test results must be determined by the microplate reader.
7. The components of different batches of this reagent shall not be mixed. Please keep the substrate away from light.
8. All samples, washing liquids and various wastes should be treated as infectious agents.
9. If there is any difference with the English manual, the English manual shall prevail
examination range:
20 pmol/L -400pmol / L
specification:
96 servings / box
Storage conditions and validity period:
1. Kit storage :; 2-8 ℃.
2. Validity: 6 months
Printing paper is mainly divided into Offset Printing Paper and double adhesive
paper.
The offset printing paper can also be called writing paper, mainly
used for printing students with the exercise book, diary, record book, Bill of
lading, books, books, teaching materials. The production machine is 1760 mm,
2640mm long network multi-cylinder paper machine. Quantitative range of
production between 55-150 g/m2. This product has white and showy, paper smooth
and delicate, writing fluency characteristic.
Double adhesive paper, also
known as double-sided offset printing paper, mainly used for special offset
printing press for a variety of color printing, cover, pictures, trademarks,
illustrations, posters, etc.. The production machine is 1760mm, 2640mm long
network multi-cylinder paper machine. Quantitative range of production is 60-150
g/m2. The product has the characteristics of smooth flow and small dust.
Offset Printing Paper
Offset Printing Paper,Paper For Offset Printing,Flexible Offset Printing Paper,Offset Printing Synthetic Paper
Mcc Meili Cloud Computing Industry Investment Co., Ltd. , https://www.mcc-offsetpaper.com